文章摘要
张天刚,孙荣禄.TC4表面单道与多道搭接激光熔覆自润滑涂层微观组织对比研究[J].材料导报,2017,31(4):47-51
TC4表面单道与多道搭接激光熔覆自润滑涂层微观组织对比研究
Comparative Study of Self-lubricating Coatings Microstructure on TC4 Alloy Surface Prepared by Single-pass Laser Cladding and Multitrack Laser Cladding
  
DOI：10.11896/j.issn.1005-023X.2017.04.011
中文关键词: 钛合金 多道搭接 激光熔覆 自润滑涂层 显微组织
英文关键词: titanium alloy, multitrack, laser cladding, self-lubricating coating, microstructure
基金项目:国家自然科学基金(51371125)；天津市应用基础及前沿技术研究计划(11JCZDJC21400)
作者单位E-mail
张天刚 天津工业大学机械工程学院, 天津 300387 113099506@qq.com 
孙荣禄 天津工业大学机械工程学院, 天津 300387
天津市现代机电装备技术重点实验室, 天津 300387 		 
摘要点击次数: 2244
全文下载次数: 1219
中文摘要:
      在TC4表面预制Ni60/20%WS2粉末,分别采用单道与多道搭接激光熔覆技术制备了自润滑涂层。结果表明,多道搭接激光熔覆层比单道激光熔覆层更容易产生裂纹,开裂方向与扫描方向有一定夹角。多道搭接激光熔覆层和单道激光熔覆层的主要成分相同,都生成了润滑相、硬质相,但多道搭接激光熔覆层中的硬质相和润滑相分布的密度较小且组织较粗大。多道搭接激光熔覆层的显微硬度分布在800～1 000HV0.5之间,单道激光熔覆层的显微硬度分布在950～1 150HV0.5之间,前者显微硬度偏低一方面是由于单道激光熔覆层的细晶强化作用,另外一方面是因为多道搭接激光熔覆层的硬质相分布密度较低。
英文摘要:
      Ni60/20%WS2 powder was precast on surface of TC4 alloy, and self-lubricating coating was then prepared by respectively adopting single-pass laser and multitrack laser cladding technology. The result showed that multitrack laser cladding was more likely to produce crack, and the cracking direction had a certain angle with the scanning direction. The main ingredients of multitrack laser-clad coating and single-pass laser-clad coating were the same, all produced lubricating phase and hard phase. But the former had lower distribution density of lubricating phase and hard phase, and coarser alloy grains. The microhardness of multitrack laser-clad and single-pass laser-clad coatings was 800-1 000HV0.5 and 950-1 150HV0.5 respectively. The grain refinement strengthening effect and higher hard phase concentration of single-pass laser-clad coating results in a relatively high microhardness compared to multitrack laser-clad coating.
查看全文   查看/发表评论  下载PDF阅读器
关闭